18
EN -
19
EN -
Weighing with tare function
The tare function enables you to reset the weight on the built-in scale to zero. This
function is useful when you want to measure an ingredient and not include the weight
of the bowl, or when you want to weigh multiple ingredients individually as you place
them into the same bowl.
1. Make sure the appliance is on and no other function is in operation.
2. Press the
SCALE / TARE
button
25
. The screen
26
shows 0000 oz / g.
3. Place the empty bowl on the scale
17
. The bowl’s weight will display.
4. Press the
SCALE / TARE
button
25
to reset the weight to zero (0000 oz / g).
5. Place the ingredient you want to weigh in the mixing bowl
5
. The weight of this
ingredient will display on the screen
26
.
6. Repeat steps 4 and 5 to weigh additional ingredients into the mixing bowl
5
.
7. Press the
MODE
button
23
to exit the weighing function.
NOTE:
If the weight exceeds 176.5 oz / 5000 g, - - - - appears on the screen.
Changing the measurement unit
• In the custom mode, press and hold the
SCALE/TARE
button
25
to change the
measurement unit from grams to ounces or vice versa.
8. Operating the appliance
For safety reasons the settings described in this chapter, can only be selected when the
mixing bowl is properly installed in the main unit and the mixing bowl lid
34
or steamer
are correctly installed.
8.1 Power supply
• Plug the power cable
8
into a suitable wall socket. The wall socket must continue to
be easily accessible after the appliance is plugged in.
8.2 Switching the appliance on and off
• Set the power switch
7
on the rear to
I
to switch on the appliance.
-
The screen
26
will light up, briefly shows the full screen display and an audio
signal sounds. Then, the appliance enters custom mode. All adjustable values are
set to 0 and the current temperature of the mixing bowl will display.
• Set the power switch
7
on the rear to
O
to switch off the appliance.
8.3 Electronic lock
This food processor has an electronic lock that is connected when the mixing bowl lid
5
or the deep steaming tray
3
are correctly installed. This is a safety function so the lid
cannot be opened easily when the blade
29
is turning.
-
This lock is always activated when the appliance cooking program is in use.
-
After the appliance stops, the lock still remains activated for 1-2 seconds.
-
An audio signal sounds and the mixing bowl lid
34
or the deep steaming tray
3
can be opened.
-
The higher the speed the longer the lock stays active, since the blade
29
and the
food keep turning longer.
8.4 Screen
• The screen
26
shows all settings and operating values.
• After approximately 5 minutes without any user interaction, the illumination of the
screen
26
goes into sleep mode. As soon as any button is pressed or a dial is turned,
the illumination of the screen
26
is switched on again for 5 minutes.
8.5 Setting the time
You can adjust the time in all modes.
1. Press the
TIME
button
21
to set the cooking time.
2. Turn the
SETTING
dial
20
clockwise to increase the time.
3. Turn the
SETTING
dial
20
counterclockwise to decrease the time.
-
You can adjust the timer from 1 second to 90 minutes. The timer setting will count
up as follows:
From
To
Time unit
1 second
1 minute
In seconds
1 minute
10 minutes
In 30-second intervals
10 minutes
90 minutes
In minutes
-
The time set is shown on the screen
26
.
-
The time is counted down after the program has started in all modes.
-
If no time and no temperature are specified, the time display will count up the time
from 0 seconds (00:00) to 90 minutes (90:00) while the blade is in operation. Then,
the appliance will be stopped automatically.
-
During operation, the time can be adjusted.
-
When the countdown is finished, the appliance stops.
-
After several seconds, an audio signal sounds.
-
The mixing bowl lid
34
can be opened.
-
The timer can be used solely as a timer when the temperature or speed settings are
not set or in use.
