background image

 

AN-000227

 

 

Document Number: AN-000227

 

Page 7 of 15

 

 

Revision: 1.0  

 

 

PROGRAMMING THE SMARTSONIC BOARD  

 

Setup SmartSonic board Jumper J1 as in Figure 1. If only one cable is used (connected to the EDBG port), 

pins 3 & 4 should be shorted. 

 

Connect the SmartSonic board to a Windows PC with EDBG USB cable.  

 

In Atmel Studio 7 select 

Tools > Device Programming

.  

 

The Device Programming screen will appear:

  

 

 

Figure 2. Device Programming Screen

 

 

Verify that the tool is 

EDBG

, device is 

ATSAMG55J19

, and interface is 

SWD

.  

 

Select 

Apply

.  

o

 

Note

: Atmel Studio 7 may require you to update the EDBG debug interface firmware on the 

SmartSonic board before continuing. Follow the on-screen instructions to update the EDBG 

firmware.  

 

The Device Programming screen will prompt to set the programming clock frequency.  Leave the clock 

frequency unchanged (use the default).  

 

Select 

Read

 near the 

Device signature 

field. The device signature bytes should be read and should not 

generate any error messages. The Device programming menu should look as follows:  

Summary of Contents for SmartSonic CH201
















Reviews: