background image

09/2013 

25 

 

TCS TürControlSysteme AG, TCS Hotline Germany: +49 41 94/ 9 88 11 88

 

Subject to technical changes. 

FAX: +49 41 94/ 9 88 129  

  Mail: [email protected]

 

PI_IMM2500     1A 

 

Cleaning 

 

!

 

Avoid water from entering the device! 
Do not use any abrasive detergents! 

 
Clean the indoor station with a dry or slightly wet cloth. 
Remove stronger stains with a standard plastic cleaner. 
 
 
 

Conformity  

 

This device meets the requirements of the EU Directive 
2004/108/EG by complying the standards EN 61000-6-3, EN 61000-6-1. 

Declarations of conformity for download under www.tcsag.de > Downloads > trade 
information. 

 
 
 

Information on disposal   

 

The adjoining symbol shows that the device has to be disposed separately from 
domestic waste.  The materials used are recyclable. Please do help protecting 
our environment and dispose the device via a collection point for electronic scrap. 
 

 

 
Dispose the parts of the packaging in collecting tanks for cardboard and paper 
resp. plastics. 

 
 
 

Warranty  

 

We offer 

a simplified processing

 in case of warranty for electrician. 

  Please observe our 

standard terms and conditions of sale

, available under 

www.tcsag.de > Downloads > trade information and enclosed in our latest catalogue. 

  Please contact us: 

[email protected]

 
 
 
 
 
 
 

Summary of Contents for IMM2500





























Reviews: