background image

 

 

 

Installation 

 

Observe when installing further devices, that you can pull out the name plate glass downwards. Do not 
mount another device below a device. 

 

Installation site 

To achieve an optimal video image quality do not point out the 
camera to  

 

solar radiation 

 

strong sources of light 

 

bright or strongly reflecting walls 

 

Mounting height 

Observe the detection angle of the camera when selecting the 
mounting height of the video front door station (see PIC on the 
right side). Persons with an average body height are detected 
optimal at a mounting height of 1.6 m above the ground.   

 

 

 

CAUTION! 

Device damage. 

The front door station must never be sealed using silicon! Condensed water must be able to escape and 
evaporate. 

 

Opening and closing the housing 

The lower aperture is connected to the aluminium profile with 
2 hexagon socket screws. 

 

Loose both screws with an allen key. 

 

Now you can face away or remove the lower aperture. 

 

Pull out the name plate glass downwards. 

 

Guide the cable through the cable gland. 

 

Mount the device to the wall using the attachment holes and 
suitable screws. 

Ensure that the wires are not getting clamped below the spac-
ers at the rear side of the front door station. 

 

Slide the name plate glass upwards below the front panel. 

 

Fix the lower aperture again. 

 

 

 

Ensure that the rubber seals within the guidance slot are not damaged when sliding in the name plate 
glass.  

 

Summary of Contents for AVD Series

























Reviews: