Taymor CONCIERGE 100 User Manual Download | Manualshive

Page: 14 / 33

background image

12

® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.

INSTALLATION

- DOOR HANDING

5

IDENTIFY THE DOOR HANDING

a. Face the door from inside

b. The door is “left-handed” if the hinges are on the left hand side of the door.

c. The door is “right-handed” if the hinges are on the right hand side of the door.

6

ADJUST INTERIOR TURN PIECE

a. Turn the turn piece to the left when it is a “right-handed” door.

b. Turn the turn piece to the right when it is a “left-handed” door.

LEFT-HANDED

RIGHT-HANDED

INTERIOR

EXTERIOR

HINGE

DOOR

«
...
12
13
14
15
16
...
»

Summary of Contents for CONCIERGE 100


































Reviews:

No comments

Related manuals for CONCIERGE 100

Lockwood 3579 Series

Brand: Assa Abloy Pages: 2

Brand: PDQ Pages: 2

Brand: Samsung Pages: 24

SafeTech F8E503

Brand: Belkin Pages: 9

SENSEON PLUS B38TREL

Brand: Accuride Pages: 3

Brand: Accuride Pages: 4

Brand: ABH Pages: 2

Brand: HOMEDEPOT Pages: 2

Brand: Roger Pages: 4

Brand: Detex Pages: 2

ADVANTEX 80 Series

Brand: Detex Pages: 19

Brand: Bauer Pages: 6

Brand: Fort Lock Pages: 1

Brand: Abus Pages: 2

Brand: Abus Pages: 4

Brand: Stock Loks Pages: 1

Brand: S4A Pages: 2

Brand: ZKTeco Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands