manualshive.com logo in svg

Taylor C723, Operator'S Manual

Share
Download
Taylor C723 Operator'S Manual Download Page 8

1-4  

TO THE INSTALLER

Model C723 

To the Installer 

1 

Refrigerant

CAUTION!

 This machine contains fluorinated 

greenhouse gases (F-Gas) to provide refrigeration using 
a hermetically sealed circuit or within foam insulation.   
This machine's type of gas, quantity, Global Warming 
Potential (GWP), and CO

2

 tonnes equivalent information 

is recorded on the machine's data label. The refrigerant 
used is generally considered nontoxic and 
nonflammable. However any gas under pressure is 
potentially hazardous and must be handled with caution.

NEVER

 fill any refrigerant cylinder completely with liquid. 

Filling the cylinder approximately 80% will allow for 
normal expansion.

CAUTION! 

Use only approved refrigerant 

listed on the machine's data label or authorized through a 
manufacturer's technical bulletin. The use of any other 
refrigerant may expose users and operators to 
unexpected safety hazards.

WARNING!

 Refrigerant liquid sprayed onto the 

skin may cause serious damage to tissue. Keep eyes 
and skin protected. If refrigerant burns should occur, 
flush the area immediately with cold water. If burns are 
severe, apply ice packs and contact a physician 
immediately.

 NOTICE! 

Taylor reminds technicians to be 

aware of government laws regarding refrigerant recovery, 
recycling, and reclaiming systems. If you have any 
questions regarding these laws, please contact the 
factory service department.

IMPORTANT!

 Refrigerants and their 

associated lubricants may be extremely moisture 
absorbent. When opening a refrigeration system, the 
maximum time the system is open must not exceed 
15 minutes. Cap all open tubing to prevent humid air or 
water from being absorbed by the oil.

Summary of Contents for C723

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands