manualshive.com logo in svg

Taylor C723, Operator'S Manual

Share
Download
Taylor C723 Operator'S Manual Download Page 51

LIMITED WARRANTY ON EQUIPMENT

10-3 

Model C723 

Limited Warranty on Equipment 

 10

LIMITATION OF WARRANTY

THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS, 

AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF 
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER'S SOLE REMEDY 
WITH RESPECT TO ANY PRODUCTS SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE COMPONENTS 
UNDER THE TERMS OF THIS LIMITED WARRANTY. ALL RIGHTS TO CONSEQUENTIAL OR INCIDENTAL 
DAMAGES (INCLUDING CLAIMS FOR LOST SALES, LOST PROFITS, PRODUCT LOSS, PROPERTY DAMAGES, 
OR SERVICE EXPENSES) ARE EXPRESSLY EXCLUDED. THE EXPRESS WARRANTIES MADE IN THIS LIMITED 
WARRANTY MAY NOT BE ALTERED, ENLARGED, OR CHANGED BY ANY DISTRIBUTOR, DEALER, OR OTHER 
PERSON, WHATSOEVER.

LEGAL REMEDIES

The owner 

must 

notify Taylor in writing by certified or registered letter to the following address,of any defect or complaint with 

the Product, stating the defect or complaint and a specific request for repair, replacement, or other correction of the Product 
under warranty, mailed at least thirty (30) days before pursuing any legal rights or remedies.

Taylor Company 

750 N. Blackhawk Blvd.

Rockton, IL  61072, U.S.A.

Summary of Contents for C723

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands