manualshive.com logo in svg

Taylor C723, Operator'S Manual

Share
Download
Taylor C723 Operator'S Manual Download Page 36

6-4  

OPERATING PROCEDURES

Model C723 

Operating Procedures 

6 

20. Slide the fork of the draw handle into the slot of the 

draw valve, starting from the right.

Figure 6-13

21. Slide the pivot pin through each draw handle as it is 

inserted into the draw valves.

Figure 6-14

Note:

This freezer features three adjustable draw 

handles to provide portion control, giving a better 
consistent quality to your product and controlling costs. 
The draw handle should be adjusted to provide a flow 
rate of 5 oz to 7-1/2 oz (148 ml to 222 ml) of product by 
weight per 10 seconds.

22. To increase the flow rate, turn the adjustment screw 

clockwise. Turn the adjustment screw 

counterclockwise to decrease the flow rate.

23. Snap the design caps over the bottom of the door 

spouts.

Figure 6-15

24. Slide the drip pan into the hole in the front panel.

\

Figure 6-16

25. Install the front drip tray and splash shield under the 

door spouts.

Figure 6-17

10529

10530

10533

10176i

101428

Summary of Contents for C723

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands