manualshive.com logo in svg

Taylor 811 series, Operator'S Manual

Share
Download
Taylor 811 series Operator'S Manual Download Page 57

LIMITED WARRANTY ON PARTS

9-3 

Model 811, 813, 819, 821 Series 

Limited Warranty on Parts 

9

LIMITATION OF WARRANTY

THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS, 

AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF 
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER'S SOLE REMEDY 
WITH RESPECT TO ANY PRODUCTS SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE PARTS UNDER 
THE TERMS OF THIS LIMITED WARRANTY. ALL RIGHTS TO CONSEQUENTIAL OR INCIDENTAL DAMAGES, 
(INCLUDING CLAIMS FOR LOST SALES, LOST PROFITS, PRODUCT LOSS, PROPERTY DAMAGES, OR 
SERVICE EXPENSES) ARE EXPRESSLY EXCLUDED. THE EXPRESS WARRANTIES MADE IN THIS LIMITED 
WARRANTY MAY NOT BE ALTERED, ENLARGED, OR CHANGED BY ANY DISTRIBUTOR, DEALER, OR OTHER 
PERSON, WHATSOEVER.

LEGAL REMEDIES

The owner must

 

notify Taylor in writing by certified or registered letter to the following address of any defect or 

complaint with the Part, stating the defect or complaint and a specific request for repair, replacement, or other 
correction of the Part under warranty, mailed at least thirty (30) days before pursuing any legal rights or remedies.

Taylor Company

750 N. Blackhawk Blvd.

Rockton, IL  61072, U.S.A.

Summary of Contents for 811 series



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands