background image

7

Fitting the valves to the existing plumbing

Note:

 If you need to remove the valve cover for ease of installation, 

remove salt lid, then simply release the two catches behind the valve 

cover and tilt top end towards you slowly, taking care not to pull off 

the wire connections. 

Please note

 that the valve cover is connected 

to the valve motor, so cannot be removed fully.

PLUMBING

Turn off the water supply at the incoming main.

FIT THE BYPASS KIT

Cut off the rising main and install the inlet tee with check valve using 

15mm reducer if required. Next, connect the bypass, inlet and outlet 

valves and outlet tee, using 15mm reducer if required. Use the 

threaded valves for the inlet and outlet and the compression valve for 

the bypass. Before turning the water back on, make sure the bypass is 

open and the inlet and outlet valves are closed. This will allow water to 

pass directly to the household system without it diverting to the water 

softener. See Valve Hard Water Bypass position diagram below.

(The use of the plastic plumbing fittings with copper pipe may affect the electrical 

earth bonding of the pipework. If in doubt, we advise that you contact a qualified 

electrician for advice).

7

Please Remember

 – 

Only use tablet or pellet salt in your softener!

6

Fitting the valves to the existing plumbing

Note:

 If you need to remove the valve cover for ease of installation, 

remove salt lid, then simply release the two catches behind the valve 

cover and tilt top end towards you slowly, taking care not to pull off 

the wire connections. Please note that the valve cover is connected to 

the valve motor, so cannot be removed fully.

PLUMBING

Turn off the water supply at the incoming main

.

FIT THE BYPASS KIT

Cut off the rising main and install the inlet tee with check valve using 

15mm reducer if required. Next, 

connect

 the bypass, inlet and outlet 

valves and outlet tee, using 15mm reducer if required

.

 Use the 

threaded valves for the inlet and outlet and the compression valve for the 

bypass. Before turning the water back on, make sure the bypass is 

open and the inlet and outlet valves are closed. This will allow water to 

pass directly to the household system without it diverting to the water 

softener. See Valve Hard Water Bypass position diagram below. 

(The use of the plastic plumbing fittings with copper pipe may affect the electrical earth

 

bonding of the 

pipework

. If in doubt, we advise that you contact a qualified electrician for 

advice).

Hard Water Bypass Position

Inlet tee 

incorporating 

check valve

Inlet closed

Bypass open 

Outlet closed

15mm reducer 

(if required)

To system 

From mains

To water  

softener inlet

From water  

softener outlet

15mm reducer 

(if required)

Valve Service Position

15mm reducer 

incorporating 

check valve

To water  

softener inlet

15mm reducer 

(if required)

Please Remember 

– Only use tablet or pellet salt in your softener!

Inlet open

Bypass closed

Outlet open

From water 

softener outlet

To system

From mains

(if required)

Inlet tee

Summary of Contents for Ultra 9

























Reviews: