Tanaka TCM 75EAP, Handling Instructions Manual

Page: 10 / 32

English
10
SPECIFICATIONS
Model TCM75EAP TCM75EBP
Engine displacement (cm
3
) 75.0
Spark Plug NGK BPMR-7A
Max. engine power by ISO 7293 (kW) 3.9
Rated engine speed by ISO 7293 (min
-1
) 9200
Max. engine speed (min
-1
) 9800
Idle engine speed (min
-1
) 2500
Fuel Tank Capacity (L) 1.1
Dry weight (kg)
Without fuel, wheel and accessories
10.4 10.6
Abrasive wheel
Wheel type Type 41
Outer diameter (mm) 305 (12") 355 (14")
Arbor hole diameter (mm) 20 (25.4 with Adapter collar)
Max. speed (min
-1
) 5100 or more
Max. Thickness (mm) 3.5 4.0
Diamond wheel
Outer diameter (mm) 305 (12") 355 (14")
Arbor hole diameter (mm) 20 (25.4 with Adapter collar)
Max. speed (min
-1
) 5100 or more
Max. Thickness (mm) 3.5 4.0
Minimum fl ange outside diameter (mm) 101.7
Wheel-fastener tightening torque (N·m) 20
Spindle diameter (mm) 20 (25.4 with Adapter collar)
Spindle max. speed (min
-1
) 4200
Sound pressure level LpA
*1
(dB(A)) by ISO 19432
Measured / Uncertainty 99.5 / 3.0
Sound power level LwA
*2
(dB(A)) by ISO 19432
Measured / Uncertainty 115 / 3.0
Vibration level (m/s
2
) by ISO 19432
Front handle
*1
/ Rear handle
*1
Uncertainty
2.2 / 2.7
1.0
2.4 / 2.9
1.0
NOTE
Noise level/vibration levels are calculated as the time-
weighted energy total for noise / vibration levels under
various working conditions with the following time
distribution:
*1: 1/7 idle, 6/7 full load.
*2: Full load.
All data subject to change without notice.
ASSEMBLY PROCEDURES
Assembly of cut-o ff wheel
1. Place the wheel (1) between the two fl anges (2), and
tighten the bolt (3) by hand. ( Fig. 6 )
2. Insert the hex. wrench (4) into the hole of arm cover (5)
and lock the spindle in place while tightening the bolt (3)
securely using the combi box spanner (6). ( Fig. 7 )
3. Make sure the rotation direction of the diamond wheel
conforms to the direction indicated on the clutch cover
and install the diamond wheel. ( Fig. 8 )
NOTE
○
When using a wheel with an arbor hole of 25.4mm, securely
attach the adapter collar (7) to the spindle. ( Fig. 9 )
○
Select and mount the correct cut-o ff wheel for the type of
work to be carried out.
Abrasive wheels Diamond wheels
Plastic (Special wheel) —
Masonry
Metal
(Special wheels)
Cast iron (Special wheels)
WARNING
○
Do not use damaged wheels. Before each use, inspect
the wheels for chips, cracks, distortion of shape or
imbalance and reject any such wheel.
○
When you use the abrasive cut-o ff wheel check the
expiration year marked (8) on the wheel before attaching.
( Fig. 10 )
There is a risk of bursting when using a wheel that it past
its expiration year.
○
Before tightening the bolt, check that the direction of the
two fl anges is correct. Also check that the fl anges are
securely installed in the fl ats of the spindle.
○
The correct tightening torque is 20 N·m. Do not tighten
more than 20 N·m.
○
Check the wheel by running it for 1 minutes at full throttle
before applying it to a workpiece.
000Book̲TCM75EAP̲SA.indb 10 000Book̲TCM75EAP̲SA.indb 10 2018/02/14 15:15:07 2018/02/14 15:15:07