Talon AC3119E4, User Manual

Page: 20 / 33

38
GB
TO INSTALL SAW CHAIN:
Always wear heavy duty gloves when handling saw chain
or making saw chain adjustments.
1. Spread chain out in a loop with cutting edges (A) point-
ing CLOCKWISE around loop (Fig. 4A).
2. Slip the chain around the sprocket (B) behind the
clutch (C). Make sure the links fit between the sprock-
et teeth (Fig. 4B).
3. Guide the drive links into the groove (D) and around
the end of the bar (Fig. 4B).
NOTE: The saw chain may droop slightly on the lower part
of bar. This is normal.
4.
Pull guide bar forward until chain is snug. Ensure all
drive links are in the bar groove.
5. Install the clutch cover making sure the tang is posi-
tioned in the lower hole in the guide bar. Make sure the
chain does not slip off of the bar. Install the bar retain-
ing nut hand tight and follow tension adjustment
instructions in Section SAW CHAIN TENSION
ADJUSTMENT.
NOTE: The guide bar retaining nuts are installed only
hand tight at this point because saw chain adjustment is
required. Follow instructions in Section SAW CHAIN
TENSION ADJUSTMENT.
• SAW CHAIN TENSION ADJUSTMENT
Proper tension of saw chain is extremely important and
must be checked before starting, as well as during any
cutting operation.
Taking the time to make needed adjustments to the saw
chain will result in improved cutting performance and pro-
longed chain life.
TO ADJUST SAW CHAIN:
1. Hold nose of guide bar up and turn adjustment screw
(A) CLOCKWISE to increase chain tension. Turning
screw COUNTERCLOCKWISE will decrease amount
of tension on chain. Ensure the chain fits snugly all
the way around the guide bar (Fig. 5).
2. After making adjustment, and while still holding nose
of bar in the uppermost position, tighten the bar
retaining nuts securely. Chain has proper tension
when it has a snug fit all around and can be pulled
around by gloved hand.
NOTE: If chain is difficult to rotate on guide bar or if it
binds, too much tension has been applied. This requires
minor adjustment as follows:
A. Loosen the bar retaining nuts so they are finger tight.
Decrease tension by turning the bar adjustment
screw COUNTERCLOCKWISE slowly. Move chain
back and forth on bar. Continue to adjust until chain
rotates freely, but fits snugly. Increase tension by turn-
ing bar adjustment screw CLOCKWISE.
B. When saw chain has proper tension, hold nose of bar
in the uppermost position and tighten the 2 bar retain-
ing nuts securely.
Fig. 3C Fig. 3D
D
E
Fig. 3E
F
G
Fig. 4A
A
Fig. 4B
D
B
C
WARNING: Always wear heavy duty gloves
when handling saw chain or making saw
chain adjustments.
Fig. 6
A
C
B
CAUTION: A new saw chain stretches,
requiring adjustment after as few as 5 cuts.
This is normal with a new chain, and the
interval between future adjustments will
lengthen quickly.
Fig. 5
A
CAUTION: If saw chain is TOO LOOSE or
TOO TIGHT, the sprocket, bar, chain, and
crankshaft bearings will wear more rapidly.
Study Fig. 6 for information concerning cor-
rect cold tension (A), correct warm tension
(B), and as a guide for when saw chain needs
adjustment (C).
GB
37
Model No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .AC3119E4 . . . . . . . . .AC3119E6 . . . . . . . .AC3119E8
Engine Displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 cm
3
. . . . . . . . . . . . .45 cm
3
. . . . . . . . . . . .45 cm
3
Rated Net Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.7 kW . . . . . . . . . . . . .1.7 kW . . . . . . . . . . . .1.7 kW
The Usable Cutting Lengths . . . . . . . . . . . . . . . . . . . . . . . . . . . .33cm . . . . . . . . . . . . . .37cm . . . . . . . . . . . . .43.5cm
Bar Cutting Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35cm . . . . . . . . . . . . . .40cm . . . . . . . . . . . . .45cm
Chain Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9.53mm (3/8”) . . . . . . .9.53mm (3/8”) . . . . . .9.53mm (3/8”)
Chain Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.27mm (0.05”) . . . . . .1.27mm (0.05”) . . . . .1.27mm (0.05”)
Idle Speed (Max.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3300 min
-1
. . . . . . . . . .3300 min
-1
. . . . . . . . .3300 min
-1
Recommended maximum speed with cutting attchment . . . . . .12500 min
-1
. . . . . . . . .12500 min
-1
. . . . . . . .12500 min
-1
Fuel Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .296 cm
3
. . . . . . . . . . . .296 cm
3
. . . . . . . . . . .296 cm
3
Oil Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .180 cm
3
. . . . . . . . . . . .180 cm
3
. . . . . . . . . . .180 cm
3
Anti Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Yes . . . . . . . . . . . . . . . .Yes . . . . . . . . . . . . . . .Yes
Drive Sprocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Teeth . . . . . . . . . . . . .6 Teeth . . . . . . . . . . . .6 Teeth
Auto Chok . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Yes . . . . . . . . . . . . . . . .Yes . . . . . . . . . . . . . . .Yes
Chain Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Yes . . . . . . . . . . . . . . . .Yes . . . . . . . . . . . . . . .Yes
Clutch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Yes . . . . . . . . . . . . . . . .Yes . . . . . . . . . . . . . . .Yes
Automatic Chain Oiler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Yes . . . . . . . . . . . . . . . .Yes . . . . . . . . . . . . . . .Yes
Low Kick-back Chain Type (Oregon) . . . . . . . . . . . . . . . . . . . .91PJ049X . . . . . . . . . .91PJ054X . . . . . . . . . .91PJ060X
Type of Guide Bar (Oregon) . . . . . . . . . . . . . . . . . . . .140SDEA318 . . . . . . . .160SDEA318 . . . . . . .180SDEA318
Low Kick-back Chain Type (Carlton) . . . . . . . . . . . . . . . . . . . .N150C-K-49E . . . . . . . .N150C-K-54E . . . . . . .N150C-K-60E
Type of Guide Bar (Carlton) . . . . . . . . . . . . . . . . . . . .9040-310107 . . . . . . . .9040-310108 . . . . . . .9040-310109
Net Weight (Without guide bar and chain) . . . . . . . . . . . . . . . . .4.9 kg . . . . . . . . . . . . . .4.9 kg . . . . . . . . . . . . .4.9 kg
Sound pressure level at ear . . . . . . . . . . . . . . . . . . . . . . . . . . . .103 dB(A) . . . . . . . . . .103 dB(A) . . . . . . . . . .103 dB(A)
Sound power level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 dB(A) . . . . . . . . . .107 dB(A) . . . . . . . . . .107 dB(A)
Guarantee sound power level . . . . . . . . . . . . . . . . . . . . . . . . . . .110 dB(A) . . . . . . . . . .110 dB(A) . . . . . . . . . .110 dB(A)
Braking Time (Max.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.12 s . . . . . . . . . . . . . .0.12 s . . . . . . . . . . . . .0.12 s
Vibration Level (Max.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 m/s
2
. . . . . . . . . . . . .15 m/s
2
. . . . . . . . . . . .15 m/s
2
Fuel Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .576.3 g/kWh . . . . . . . .576.3 g/kWh . . . . . . . .576.3 g/kWh
SPECIFICATIONS
• TOOLS FOR ASSEMBLY
You will need these tools to assemble your chain saw:
1. Combination wrench-screwdriver (contained in your
user’s kit).
2. Heavy duty work gloves (user supplied).
• ASSEMBLY REQUIREMENTS
Your new chain saw will require adjustment of chain, filling
the fuel tank with correct fuel mixture and filling the oil tank
with lubricating oil before the unit is ready for operation.
Read the entire user manual before attempting to oper-
ate your unit. Pay particular attention to all safety
precautions.
Your user manual is both a reference guide and handbook
provided to furnish you with general information to
assemble, operate and maintain your saw.
• GUIDE BAR / SAW CHAIN / CLUTCH
COVER INSTALLATION
TO INSTALL GUIDE BAR:
To ensure the bar and chain receive oil, ONLY USE THE
ORIGINAL STYLE BAR with the oil passage hole (A) as
illustrated above. (Fig. 3A)
1. Make sure the CHAIN BRAKE lever is pulled back into
the DISENGAGED position (Fig. 3B)
2. Remove the bar retaining nut (B). Remove the CHAIN
BRAKE cover (C) by pulling straight out, some force
may be required. (Fig. 3C).
Note: Discard the two plastic washers.They are only used
for shipping the chain saw.
3. Using a screwdriver, turn the adjustment screw (D)
COUNTERCLOCKWISE until the TANG (E) (projecting
prong) is to the end of its travel (Fig. 3D).
4. Place the slotted end of the guide bar over the bar bolt
(F). Slide guide bar behind clutch drum (G) until the
guide bar stops (Fig. 3E).
ASSEMBLY INSTRUCTIONS
WARNING: DO NOT start saw engine until
unit is properly prepared.
WARNING: Always wear protective gloves
when handling chain.
Fig. 3A
A
Fig. 3B
C
B