TallyGenicom LGe06 Operator'S Manual Download Page 77

Page: 77 / 108

Chapter 3:

Printer Menus and the Control Panel

3–77

IntelliFilter Category

Use the Arrow and Enter keys to select

Menu => Config Menu => IntelliFilter to

get here.

IntelliFilter is a programmable feature,

standard on TallyGenicom line printers. Without having to touch an otherwise

well-working host system, IntelliFilter permits users to free their systems from

hard coded dependence on a specific printer that is no longer maintainable, or

able to meet the demands of the application.

Serial
Parallel
Twinax/Coax
LAN

These four parameters can be set to either Enable or Disable the IntelliFilter on

their respective ports.

File Management

Selecting

Download

, places the printer in the IntelliFilter download mode.

Delete

will delete the currently downloaded IntelliFilter.

Use the Arrow and Enter keys to select Menu => Config Menu => Printer =>

Report => IntelliFilter to print the currently downloaded IntelliFilter.

Config Menu

⇒

IntelliFilter

Summary of Contents for LGe06













































































































Search results

Summary of Contents for LGe06

Reviews:

Related manuals for LGe06

Brands by name

Popular brands

TallyGenicom LGe06, Operator'S Manual

Search results

Summary of Contents for LGe06

Reviews:

Related manuals for LGe06

Brands by name

Popular brands