TallyGenicom LGe06 Operator'S Manual Download Page 72

Page: 72 / 108

3–72

Operator Manual

How to label a configuration slot

•

Make sure the printer is Offline.

•

Press the Menu key to enter Menu mode.

•

Use the Up and Down Arrow keys to get to the Config menu, and then

press Enter.

•

Use the Up and Down Arrow keys until the display reads Configurations,

then press Enter.

•

Use the Up and Down Arrow keys until you see Config n label, where n is

the number of the configuration you want to label (1-10). Press Enter.

•

A cursor appears underneath the first letter (C). Use the Up and Down

Arrow keys to scroll to the number or letter you want to use. Repeat for

up to 15 characters, pressing Enter after each letter. You must press

Enter 15 times even if your label is shorter.

•

Press Clear or Menu to save it. Now, when you use SAVE or LOAD, this

configuration name appears in the slot you've chosen.

Config Menu

⇒

Configurations

Summary of Contents for LGe06













































































































Search results

Summary of Contents for LGe06

Reviews:

Related manuals for LGe06

Brands by name

Popular brands

TallyGenicom LGe06, Operator'S Manual

Search results

Summary of Contents for LGe06

Reviews:

Related manuals for LGe06

Brands by name

Popular brands