Talgil DREAM 2 Page 9 Installation Manual Download

Page: 9 / 61

The

USB

socket can be used for connecting

USB

memory sticks for uploading/downloading the

image files into the controller or for updating the software version. Another use of the

USB

socket will be for connection of a Netsctick for cellular communication (see below).

In case the communication is meant to be through the

Ethernet

LAN

(

ocal

rea

etwork),

the two

Ethernet sockets

will be used. The internal socket is for connection between the

Mother board

and the

Ethernet card

(attached on top of the CPU board), the external

socket is for the cable that goes to the

Ethernet

source on site.

1.1.3

The CPU board

The

CPU board

can be found underneath the front panel, at the back of the

LCD display.

Let’s get familiar with some of the components on the CPU board:

The

Cellular modem

and the

Ethernet card

are two of the three options for connection to

the internet. The third is a

USB Netstick

that can be plugged into the

Mother board

The

Lithium battery

keeps the internal clock running while the

CPU board

is disconnected

from energy source.

Ethernet card

Reset button

LCD contrast

adjustment

Power ON

indication LEDs

Remote I/O

communication LEDs

Buzzer

CPU board

Cellular modem

The CPU chip

Lithium battery

USB Netstick

Summary of Contents for DREAM 2






























































Search results

Summary of Contents for DREAM 2

Reviews:

Related manuals for DREAM 2

Brands by name

Popular brands

Talgil DREAM 2, Installation Manual

Search results

Summary of Contents for DREAM 2

Reviews:

Related manuals for DREAM 2

Brands by name

Popular brands