Talgil DREAM 2 Page 4 Installation Manual Download

Page: 4 / 61

THE SYSTEM STRUCTURE

The

DREAM 2

irrigation control system is the second generation of the well-known

DREAM

controllers. Additionally to the outstanding features of the previous generation, the

DREAM 2

now equipped with a more powerful processor, with a much bigger memory capacity and above

all it now offers internet communication, supported by a powerful

SERVER

. Users and

technicians can now access the controllers from everywhere anytime. Upgrading from

DREAM 1

DREAM 2

is involved with replacement of three boards only: the

CPU

, the

Mother board

and the

Power supply

board.

The following schematic diagram describes the principal structure of the

DREAM 2

system

which apart from the internet communication resembles very much the structure of

DREAM 1

Summary of Contents for DREAM 2






























































Search results

Summary of Contents for DREAM 2

Reviews:

Related manuals for DREAM 2

Brands by name

Popular brands

Talgil DREAM 2, Installation Manual

Search results

Summary of Contents for DREAM 2

Reviews:

Related manuals for DREAM 2

Brands by name

Popular brands