background image

219

OPTIONS

Immobilizer System

5. Return to the OFF (O) position from the

ON ( I ) position and remove the
registration key.

6. Within 10 seconds, insert the immobilizer

key into the starter switch and turn it from
the OFF (O) position to the ON ( I )
position.

7. Hold for about 10 seconds.

8. Return to the OFF (O) position from the

ON ( I ) position and remove the
immobilizer key.

9. Perform steps (6) to (8) for all immobilizer

keys (maximum of 5 keys) that you wish
to register.

10. Within 10 seconds after registering the

immobilizer keys, insert the registration
key into the starter switch and turn it from
the OFF (O) position to the ON ( I )
position.

11. Hold for about 10 seconds.

12. Return to the OFF (O) position from the

ON ( I ) position and remove the
registration key.
This completes the registration procedure.

13. Check that the engine starts using all the

registered keys (registration key and
immobilizer keys).
If the engine does not start, re-register
the keys.
If the engine still does not start, consult a
Takeuchi sales or service outlet.

N0B030E

Registration key

N0B027E

Immobilizer key

N0B028E

Immobilizer key

N0B029E

Registration key

N0B030E

Registration key

Summary of Contents for TB175








































































































































































































































Reviews: