manualshive.com logo in svg

TAG MIL-BOOK 100 Series, Operator'S Manual

Share
Download
TAG MIL-BOOK 100 Series Operator'S Manual Download Page 4

Please note:

The use of a non-shielded interface cable with this equipment is prohibited.

Canada

Canadian Department of Communications

Radio Interference Regulations Class B Compliance Notice

This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus set out in the Radio Interference Regulations of the Canadian
Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les
limites applicables aux appareils numériques de la classe B prescrites dans le Règlement
sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.

Products with the CE Marking comply with both the EMC directive (89/336/EEC) and
the Low Voltage Directive (73/23/EEC) issued by the Commission of the European
Community.

Compliance with these directives implies conformity to the following European Norms:

l

 EN50081-1:  Electromagnetic compatibility-Generic emission standard

l

 EN55022: conducted Emission, Radiated Emission

l

 EN61000-3-2: Current Harmonic

l

 EN61000-3-3: Voltage Flicker

l

 EN50082-2: Electromagnetic compatibility-Generic immunity standard

l

 IEC1000-4-2: Electrostatic Discharge

l

 IEC1000-4-3: Radiated Susceptibility

l

 IEC1000-4-4: Electrical Fast Transients

l

 IEC1000-4-5: Surge Test

l

 IEC1000-4-6: Conducted Susceptibility

l

 IEC1000-4-11: Voltage Dip and Interruption

The Products pass C-UL, UL, TUV approved to comply with EN60950 standard.

Summary of Contents for MIL-BOOK 100 Series




































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands