manualshive.com logo in svg

TAG MIL-BOOK 100 Series, Operator'S Manual

Share
Download
TAG MIL-BOOK 100 Series Operator'S Manual Download Page 120

Troubleshooting

8-7

The external monitor displays nothing.

l

 Make sure that the monitor is turned on.

l

 Make sure that the monitor’s signal cable is properly connected.

l

 Check if the Setup item 

Display Mode

 on the Main menu of the SCU

  program is configured correctly.

l

 Switch the display to the monitor by pressing 

Fn

+

F9

 or through the

  Windows’ 

Display

 properties.

Simultaneous display does not work.

l

 Make sure that you turn on the external monitor before turning on the

  computer.

l

 Check the Setup item 

Display Mode

 on the Main menu of the SCU

  program is configured correctly.

l

 Press 

Fn

+

F9

 or use Windows’ 

Display

 properties to select the display

  options.

Floppy Disk Drive Problems (on optional docking station)

The Floppy Disk Drive In-use Indicator stays on.

l

 Make sure that the floppy disk is not physically damaged.

l

 Make sure that the floppy disk is inserted correctly.

The disk drive cannot write to a floppy disk.

l

 Make sure that the floppy disk is formatted.

l

 Make sure that the floppy disk is not write-protected.

l

 Make sure that you are writing to the correct drive.

l

 Make sure that there is enough space left on the floppy disk.

l

 Make sure that the floppy disk is not physically damaged.

Summary of Contents for MIL-BOOK 100 Series




































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands