TAG MIL-BOOK 100 Series Page 28 Operator'S Manual Download | Manualshive

Page: 28 / 131

background image

Getting Started

1-13

Attaching and Detaching the Computer To/From the

Docking Station

WARNING:

Make sure that the computer is off before connecting it to or

disconnecting it from the docking station to prevent damage to either computer or

docking station.

Attaching the Docking Station

To attach the computer to the docking station:

1.

Place the docking station on an upright position with the floppy and

CD drives in front facing you.

Slowly place the computer on top of the docking station slightly
inclined toward the front and carefully align the small rectangular holes
located in front near the edge of the computer to the two small hooks,
also located in the front top edge of the docking station to connect
together.

Press on the back portion to connect the computer to the docking
station.

Detaching the Computer

To detach the computer from the docking station:

2.

Place both index and middle fingers firmly on the side locking latch

and press firmly while at the same time using both thumbs to pull up
the rear side of the computer.

3.

Slide the computer slightly toward the rear to separate the small

rectangular holes located in front near the edge of the computer
from the two small hooks, also located in the front top edge of the
docking station.

4.

Lift the computer away from the docking station.

«
...
26
27
28
29
30
...
»

Summary of Contents for MIL-BOOK 100 Series




































































































































Reviews:

No comments

Related manuals for MIL-BOOK 100 Series

Toughbook CF-74JCL02AM

Brand: Panasonic Pages: 36

Brand: Macrovision Corporation Pages: 212

Brand: Clevo Pages: 82

Barbie B-Bright

Brand: Oregon Scientific Pages: 16

TravelMate TMP215-52

Brand: Acer Pages: 48

Brand: Acer Pages: 31

Toughbook CF-M34NPFZPM

Brand: Panasonic Pages: 32

Brand: IVIEW Pages: 16

A105-S4004 - Satellite - Core Duo 1.66 GHz

Brand: Toshiba Pages: 10

Brand: Toshiba Pages: 10

Brand: Toshiba Pages: 11

Brand: Toshiba Pages: 10

Brand: Toshiba Pages: 11

Brand: Toshiba Pages: 11

Brand: Toshiba Pages: 11

Brand: Toshiba Pages: 11

Brand: Toshiba Pages: 11

Brand: Toshiba Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands