manualshive.com logo in svg

TAG MIL-BOOK 100 Series, Operator'S Manual

Share
Download
TAG MIL-BOOK 100 Series Operator'S Manual Download Page 115

 Troubleshooting

8-2

Preliminary Checklist

Here are helpful hints to follow before you take further actions
when you encounter any problem:

l

 Try to isolate which part of the computer is causing the problem.

l

 Make sure that you turn on all peripheral devices before turning on

  the computer.

l

 If an external device has a problem, make sure that the cable

  connections are correct and secure.

l

 Make sure that the configuration information is properly set in the

  SCU program.

l

 Make sure that all the device drivers are correctly installed.

l

 Make notes of your observations. Are there any messages on the

  screen? Do any indicators light? Do you hear any beeps? Detailed
  descriptions are useful to the service personnel when you need to
  consult one for assistance.

If any problem persists after you follow the instructions in this
chapter, contact an authorized dealer for help.

Summary of Contents for MIL-BOOK 100 Series




































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands