SyxthSense SYX66 Series Commissioning Manual Download Page 8

Page: 8 / 61

SYX66x Commissioning Guide

V1.10.3 300117

Page 8 of 61

1.6 WEB BROWSER CONNECTION

Customer Interface is possible using a Web Browser, Smart Phone (with SYX66x connected to a network with Wi-Fi
access). Users can quickly:

•

Check current status of control system

•

Change User level

•

Change of settings

•

View historic information

•

Time Schedule and Holiday Planning

•

Configuration of all the controller options

•

Remote overrides and time extensions

•

Observe Live Controller Operation

IP: 192.168.1.99

SM: 255.255.255.0

DG: 192.168.1.1

Users must ensure that their chosen device is configured to be on the same network range to ensure that a
connection can be made. For more information please see the Laptop Fixed IP config video on SyxthSense Video
Resource Library

http://www.syxthsense.com/video_resources

Summary of Contents for SYX66 Series






























































Search results

Summary of Contents for SYX66 Series

Reviews:

Related manuals for SYX66 Series

Brands by name

Popular brands

SyxthSense SYX66 Series, Commissioning Manual

Search results

Summary of Contents for SYX66 Series

Reviews:

Related manuals for SYX66 Series

Brands by name

Popular brands