background image

SyxthSense Ltd

Copyright © 2018 SyxthSense Ltd. All rights reserved - 04/2018 

PS 

MOD3.103

 - 16/23

Online store: 

www.syxthsense.com

Enquiries: T: 

44 (0)1392 875 414   

E:

 [email protected]

FUNCTION CODE 03 - READ HOLDING REGISTERS  (For Modicon Addressing Add 40,000)
FUNCTION CODE 06 - WRITE SINGLE HOLDING REGISTER 
FUNCTION CODE 16 - WRITE MULTIPLE HOLDING REGISTERS

100

Nominal Setpoint

Unsigned 16

0...990

0...99.9 (Default 70.0)
(°C/°F/%)

101

Setpoint Unit

Unsigned 16

0..1

0 = Temperature (Default)
1 = Percentage

102

Sensor 3 Source

Unsigned 16

0..1

0 = Buillt-In Sensor (Default)
1 = Network Sensor

103

Sensor 3 Network Temperature

Signed 16

-580...1220

-58.0...122.0°C/°F (Default 0.0)

104

Minimum Setpoint

Unsigned 16

0...990

0.0...99.9°C/°F/% (Default 57°F)

105

Maximum Setpoint

Unsigned 16

0...990

0.0...99.9°C/°F/% (Default 86°F)

106

Colour Ring Mode

Unsigned 16

0..10

0 = White
1 = Red
2 = Blue
3 = Green
4 = Orange
5 = Yellow
6 = Magenta
7 = Cyan
8 = Sensor 1
9 = Sensor 2
10 = Sensor 3 (Default)

107

Sensor 1 Source

Unsigned 16

0..1

0 = RI1
1 = Network Sensor (Default)

108

Sensor 1 Network Temperature

Signed 16

-580...1220

-58.0...122.0°C/°F (Default 0.0)

109

Fan Manual Control Mode

Unsigned 16

0..4

0 = Disabled (default)
1 = 1-Step
2 = 2-Step
3 = 3-Step
4 = 6-Step
5 = 1-Step + Auto
6 = 2-Step + Auto
7 = 3-Step + Auto
8 = 6-Step + Auto
9 = Advanced

110

Fan Display

Unsigned 16

0..5

0 = Disabled (default)
1 = Bar & Fan
2 = Bar
3 = Fan
4 = Coloured Bar & Fan 
5 = Coloured Bar 

111

Fan Speed Override

Unsigned 16

0..6

0..6

112

Enable Mode Icon

Unsigned 16

0..6

0 = Disabled (default)
1 = Htg/Clg 
2 = Htg/Clg/Fan 
3 = Auto/Htg/Clg
4 = Auto/Hhg/Clg/Fan
5 = Auto/Htg/Fan
6 = Auto/Clg/Fan

113

Digital Input Mode

Unsigned 16

0..6

0 = Disabled (no SRI effect)
1 = Close for ECO
2 = Open for ECO 
3 = Close for OFF
4 = Open for OFF
5 = DI Contact Alarm
6 = Network

114

Digital Input Delay

Unsigned 16

0..7200

0..7200 seconds (Default 0s)

115

Enable Lights Symbol

Unsigned 16

0..1

0 = Disabled (default)
1 = Enabled

116

Enable AC Symbol

Unsigned 16

0..1

0 = Disabled (default)
1 = Enabled

117

Lock Mode

Unsigned 16

0..3

0 = Lock mode disabled (default)
1 = On/Off/Boost workable only
2 = Temp settings only available
3 = All buttons disabled

118

Show Unit Swap

Unsigned 16

0..1

0 = Disabled
1 = Enabled  (default)

Register

Parameter Description

Data Type

Raw Data

Range

Summary of Contents for SRI-75 Series
























Reviews: