background image

FCC Compliance Statement  

This device complies with part 15 of the FCC rules. Operation is 
subject to the following two conditions: (1) this device may not 

cause harmful interference, and (2) this device must accept any 

interference received, including interference that may cause 
undesired operation.  

 

This product is intended to be supplied by a UL listed Direct Plug-IN 

Power Supply marked “Class 2” or a UL listed ITE Power Supply 
marked “LPS” with output rated 12VDC, 5A or higher. This 

equipment has been tested and found to comply with the limits for 

a Class B digital device, pursuant to Part 15 of FCC Rules. These 
limits are designed to provide reasonable protection against 

harmful interference in a residential installation. This equipment 

generates, uses, and can radiate radio frequency energy and, if not 
installed and used in accordance with the instructions, may cause 

harmful interference to radio communications. However, there is no 

guarantee that interference will not occur in a particular 

installation. If this equipment does cause harmful interference to 
radio or television reception, which can be determined by turning 

the equipment off and on, the user is encouraged to try to correct 

the interference by one or more of the following measures: 

 

• 

Re-orient or relocate the receiving antenna. 

• 

Increase the separation between the equipment and 
receiver. 

• 

Connect the equipment into an outlet on a circuit different 

from that to which the receiver is connected 

• 

Consult the dealer or an experienced radio/TV technician 
for help. 

 

Use of shielded cables is required to comply with the Class B limits 
of Part 15 of the FCC Rules. You are cautioned that any changes or 

modifications not expressly approved in the included manual could 

void your authority to operate and/or obtain warranty service for 
this equipment.

161 

Summary of Contents for DiscMaster 101P





































































































































































Reviews: