42/70 |
FDS...EX
Installation, 5.1 - ON & OUT of the wall EI90S
Using 2 layers of Mineral Wool
TIP: The duct-wall cavity filling can be also replaced by plaster/mortar/concrete (F2) as a replacement of filling (F9),
then the coating (F10) is not needed for the cavity filling.
1. The supporting construction opening must be prepared as depicted. Opening surfaces must be even and cleaned
off. The flexible wall opening must be reinforced as per the standards for plasterboard walls. The opening
dimensions are driven by the nominal dimensions of the damper with added clearance. For rectangular dampers,
the opening will have the dimensions of W1 and H1.
2. Insert the duct into the load-bearing structure along with the damper in such a way that the duct will stick out of
the wall to the needed distance. Press the insulation around the duct (F9) and cut its edges to even it with the wall
surface. Paint the insulation surface in alignment with the wall with a suitable coat of paint (F10) up to 100 mm
from the duct to cover the insulation and part of the wall. Or use filling (F2) as per WET installation.
3. Hang the square damper, surrounded in its perimeter with U-profiles (22) or tubular frame, in the blade location
onto the threaded rods (20) min. M10.
4. Insulate the damper and duct parts between the damper and the wall. Glue the insulation onto the wall using
suitable fire-resistive coating (F10).
5. Secure the insulation:
• for FDS-3G onto the square duct in two 90 mm layers. Using 90 mm (1st layer) and 180 mm (2nd layer) long welding
pins (18, 19).
• for FDS-EI90S onto the square duct in two 100 mm layers. Using 100 mm (1st layer) and 200 mm (2nd layer) long
welding pins (18, 19).
6. Cover the insulation face and perimeter up to 150 mm from the insulation edge using galvanized sheet metal
(accessory A3), secure the sheet against the damper housing through accessories holes. Any protruding screws
which could stand in the way of the blade during its opening need to be shortened so that they don’t prevent blade
movement.
7. If needed, uncover and clean the damper after installation.
8. Make sure the fixing screws are not interfering with the blade movement and check the damper’s functionality.
Duct rules
The rules for hanger placement and duct suspension depend on the damper’s distance from the supporting
construction. The desired distance from the wall to the end of the duct connection with the damper divides the rules
into two groups:
• Distance from 35 mm to max. 1500 mm.
• Distance greater than 1500 mm
Installation Distances
For installation 5.1 ON & OUT, the minimum distance from the wall or ceiling to the damper body is 40 mm. For multiple
crossings through a fire-resistive wall the minimum distance between two damper bodies is 400 mm. The distance of
200 mm applies for distances between the damper and a nearby foreign object crossing the fire-resistive wall.
5.1
On, Out
FDS-3G...EX
100 × 100 ...
... 1200 × 800
EI 60 (v
e
- i ↔ o) S
a)
b)
EI 90 (v
e
- i ↔ o) S
Summary of Contents for FDS-3G EX Series
