SystemAir AW 400 EC sileo Operating Instructions Manual Download Page 15

Operating instructions

2. INTENDED USE

The device is exclusively designed as a built-in device for conveying

air according to its technical data.

Any other usage above and beyond this does not conform with the

intended purpose and constitutes misuse of the device.

Customer equipment must be capable of withstanding the mechanical

and thermal stresses that can arise from this product. This applies for the

entire service life of the equipment in which this product is installed.

Intended use also includes

Using the device only in stationary systems.

Performing all maintenance work.

conveying air at an ambient air pressure between 750 mbar and 1050

mbar.

Using the device within the permitted ambient temperature range; see

Chapter 3.6 Transport and storage conditions and

Chapter 3.2 Nominal data.

Operating the device with all protective devices.

Following the operating instructions.

Improper use

In particular, operating the device in the following ways is prohibited and

could be hazardous:

Operating the device in an unbalanced state, e.g. due to dirt deposits

or ice formation.

Resonant operation, operation with severe vibration. This also

includes vibration transmitted to the fan from the customer installation.

Operation in medical equipment with a life-sustaining or life-support

function.

Operation with external vibrations.

Conveying solids in the flow medium.

Painting the device

Connections (e.g. screws) coming loose during operation.

Opening the terminal box during operation.

Conveying air that contains abrasive particles.

Conveying highly corrosive air, e.g. salt spray. Exception: devices

designed for salt spray and correspondingly protected.

Conveying air with high dust content, e.g. suctioning off sawdust.

Operating the device close to flammable materials or components.

Operating the device in an explosive atmosphere.

Using the device as a safety component or to perform safety-related

functions.

Operation with completely or partially disassembled or manipulated

protective devices.

In addition, all applications not listed among the intended uses.

Summary of Contents for AW 400 EC sileo


























Reviews: