background image

pag.

 

7

Industrial PC - MONITOR COPILOT 21,5"

 Order Code 2E000xxx

May 2018 - Rev. 1.1

Power: 

 

Power  On/Power  off:  Do  not  use  this 

button to avoid keeping the monitor off even with the 

incoming video signal.

Menu: 

 

Enable the menu display for configura

-

tion

Select: 

 

Menu select function

The 

Up / Down

 keys allow you to change the preset 

values

If you are not inside the Menu, the keys enable the 

following functions:

• 

Select:

 Select VGA/DVI input video source 

(

auto

 default)

• 

Down:

 Automatic color calibration

• 

UP: 

 

Automatic synchronism calibration

The Menu allows you to change the following parame-

ters:

Picture

 

Brightness
Contrast 
Sharpness 
Position H
V Position
Clock
Phase

Color

 

Color Status  Management  User  (User, 

Warm, Normal, Cool)
Red  
Green  
Blue  

Auto Color To Start

 

SETUP

 

Source RGB, DVI, 

AUTO

  

Factory reset  To Start

Aspect (off/on)
Set ID (off/on)

Pin N. Symbol  

Description

1

TMDS DATA2-

TMDS DATA2 Differential 

Negative Signal

2

TMDS DATA2+  

TMDS DATA2 Differential 

Positive Signal

3

TMDS DATA2 Shield

Shield  Shield for TMDS 

Channel  #2

4

NC  

Not connected

5

NC  

Not connected

6

DDC Clock

The Data Line for the DDC 

Interface

7

DDC Data

The Clock Line for the DDC 

Interface

8

NC  

Not connected

9

TMDS DATA1-

TMDS DATA1 Differential 

Negative Signal

10

TMDS DATA1+

TMDS DATA1 Differential 

Positive Signal

11

TMDS DATA1 Shield

Shield for TMDS Channel  

#1

12

NC  

Not connected

13

NC  

Not connected

14

+5V Power

+5 Volt signal for EDID 

(Un-powered  Monitor)

15

GND (for +5V)

Ground for +5 Volt Power 

pin, Sync return

16

HPD

Identify the presence of a 

monitor

17

TMDS DATA0-

TMDS DATA0 Differential 

Negative Signal

18

TMDS DATA0+

TMDS DATA0 Differential 

Positive Signal

19

TMDS DATA0 Shield

Shield for TMDS Channel  

#0

20

NC  

Not connected

21

NC  

Not connected

22

TMDS CLOCK Shield

Shield for TMDS Clock 

differential Pair

23

TMDS CLOCK+

TMDS DATA0 Differential 

Positive Signal

24

TMDS CLOCK-

TMDS DATA0 Differential 

Negative Signal

C1

NC  

Not connected

C2

NC  

Not connected

C3

NC  

Not connected

C4

NC  

Not connected

C5

NC  

Not connected

Table 7.1.1

7. Available 

connectors

7.1 Signal Input Analog RGB, 

TMSD (DVI)

Summary of Contents for 2E000208










Reviews: