Synthes USS II Manual Download Page 49 | Manualshive

Page: 49 / 76

background image

Synthes

47

2

Insert rod for transverse connector

The special design of the transverse connection sleeve with
the two indentations on the upper side means that the trans-
verse connector rod can be angled by up to ± 20° depending
on anatomical conditions.

Determine the appropriate length of the rod for transverse
connector

3.5 mm. If necessary, cut the rod to size with

the rod cutting and bending device.

Hold the clamp with the small hexagonal screwdriver and
pass the cross-link rod

3.5 mm through the hole in

the cross-link clamp. If necessary, use the holding forceps to
insert the rod for transverse connector. Tighten the set screw
of the cross-link clamp firmly with the small hexagonal
screwdriver.

3

Mount second cross-link clamp

Repeat the procedure described in Step 1 for the second
clamp on the opposite rod.

Pass the cross-link rod

3.5 mm through the hole in the

second clamp so that it projects 5 mm above the clamp.
Tighten the set screw firmly with the small hexagonal screw-
driver.

«
...
47
48
49
50
51
...
»

Summary of Contents for USS II













































































Reviews:

No comments

Related manuals for USS II

Brand: Omnia Pages: 8

Brand: MagCore Pages: 80

Brand: MagCore Pages: 80

Brand: YASKAWA Pages: 81

Brand: YASKAWA Pages: 52

Brand: ubicquia Pages: 36

Cutler-Hammer ATC-300

Brand: Eaton Pages: 32

Brand: AVID LABS Pages: 20

Brand: Briteq Pages: 12

Brand: Crary Pages: 56

Brand: Osram Pages: 30

Spacelabs Medical 92506

Brand: OSI Systems Pages: 92

VL4000 BeamWash Luminaire

Brand: Vari Lite Pages: 190

Life/form LF03608

Brand: Nasco Healthcare Pages: 6

Brand: Beta Pages: 8

Brand: Halemeier Pages: 2

Brand: IRUDEK Pages: 19

Brand: RAK Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands