Synthes USS II Manual Download Page 48 | Manualshive

Page: 48 / 76

background image

46

Synthes

USS II

Handling technique

Connecting Two Rods

Variation A: Connecting Two Rods
with 6 mm Cross-link Clamps

Instruments

314.070 Screwdriver, hexagonal, small,

2.5 mm,

with groove

388.363 Holding Sleeve with Catches,

for No. 314.070

388.450 Holding Forceps for USS Rods

3.5/4.5 mm, length 295 mm

Optional instruments

388.750 USS Rod Cutting and Bending Device

388.410 Spreader Forceps for Pedicle Screws,

length 330 mm

Transverse connectors are horizontal stabilizers that connect
the two longitudinal rods thus significantly increasing
structural rigidity. They are recommended for unstable frac-
tures and multi-segmental constructions.

1

Mount first cross-link clamp

Assemble the small hexagonal screwdriver and the holding
sleeve with locking catches. Retract the holding sleeve.

To pick up the pre-assembled cross-link clamp, insert the
hexagonal screwdriver in the fixing screw of the clamp, push
the holding sleeve downwards and the locking catches over
the sleeve of the cross-link clamp.

Retract the holding sleeve slightly, place the clamp on the
rod and let go of the holding sleeve.

«
...
46
47
48
49
50
...
»

Summary of Contents for USS II













































































Reviews:

No comments

Related manuals for USS II

Brand: Walker Bay Pages: 8

Brand: National Instruments Pages: 16

Brand: Jasco Pages: 11

Tetrix 351 AC/DC Smart FW

Brand: EWM Pages: 117

Brand: Raytech Pages: 21

Brand: Teac Pages: 2

Brand: laerdal Pages: 2

Brand: Barreto Pages: 20

Brand: Barreto Pages: 18

Brand: Backyard Discovery Pages: 41

Brand: LAWO Pages: 459

Brand: earline Pages: 13

Brand: T-Rex Pages: 13

Brand: GE Pages: 212

Brand: Gary Machinery Pages: 14

Brand: Hakko Electronics Pages: 8

Professional HS 8

Brand: Hailo Pages: 5

Brand: Hainbuch Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands