Synthes USS II Manual Download Page 31 | Manualshive

Page: 31 / 76

background image

5

4

Position the socket wrench/holding sleeve connection above
the implant (screw or hook) (4). Place sleeve and nut to-
gether using the socket wrench handle (5).

2

Tighten the nut finger-tight

Tighten the nut using the socket wrench for twelve point nut
with L-handle. The socket wrench for the countertorque is
spring-loaded and can be pressed downwards continuously
with the left hand using the T-handle. To tighten the nut
further, lift the L-handle of the socket wrench with the right
hand and engage it again.

Note:

If using a 6 mm rod, a few threads will remain visible

on the nut.

Synthes

29

«
...
29
30
31
32
33
...
»

Summary of Contents for USS II













































































Reviews:

No comments

Related manuals for USS II

Brand: Rangevision Pages: 31

Brand: Cannon Pages: 40

Brand: NARGESA Pages: 34

Brand: Dana Design Pages: 20

Brand: Hacker Pages: 2

Brand: J.P. SELECTA Pages: 8

Brand: Haemonetics Pages: 134

Brand: Hadeco Pages: 72

Brand: Hakko Electronics Pages: 8

Professional HS 8

Brand: Hailo Pages: 5

Brand: Hainbuch Pages: 52

ST60+ SPEED INSTRUMENT

Brand: Raymarine Pages: 60

Brand: Raymarine Pages: 15

Brand: RaycoWylie Pages: 9

Brand: Raven Pages: 58

Brand: Raven Pages: 26

Brand: Ravo Pages: 114

Brand: Alcoscan Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands