manualshive.com logo in svg

Synesso Sabre, Owner'S Manual

Share
Download
Synesso Sabre Owner'S Manual Download Page 20

 

19

DigiZone

™

 

Control Reset & Reboot Guide  

If your electronics are out of the parameters you set and you are unable to make any adjustments, follow 
these steps to reset the electronics. 

Section A – Reset DigiZone™ Electronics

 

1.  Turn the red on/off 

power switch

 OFF, then back ON 

2. Scroll the 

zones 

 and press 

set 

to check the set points, reset if required  

3.  Press and hold the 

up arrow,

 then press and hold the 

zone 

button, hold both buttons together for 5 

seconds to enter the common parameter adjusting mode. 

•

  1

st

 parameter is the 

high alarm

, set to 275° F – holding the 

set

 button and using the 

up

 and 

down arrow

 keys. Press 

zone

 to go to the next parameter 

•

  2

nd

 parameter is the 

low alarm

, set to 125° F 

•

  3

rd

 parameter is the 

auto fill probe

 

delay

, factory setting is 5 seconds 

•

  4

th 

- 8

th

 parameters are the 

temperature offset for Zone 1, 2, 3, 4 & 5 respectively. 

The 

factory offsets for this machine are located on page 2 under the serial number 

4. Press 

zone

 button to return to the operational mode 

 

If the electronics do not respond to the above procedure, then a total system reboot is required

  

 

Section B – Total System Reboot

 

1.  Turn red on/off 

power switch

 OFF and then turn the 

element breaker

 OFF 

2.  This can be difficult and may require assistance, press and hold 

zone

, 

up arrow

, 

down arrow 

and 

set

 buttons simultaneously, and turn the 

power switch

 ON.  Continue to hold all buttons during the 

start up process and wait until the electronics 

turn on

 momentary, 

then off

 and 

then on

 again 

BEFORE you release the buttons. If 2 

ON

 cycles are not achieved, please try again.  

3.  Release all 4 buttons 
4.  This is a total system reboot and all of your parameters and your temperature set points will need to 

be reentered. The electronics will show the factory temperature set points. Follow steps 1 -4 in 
section A to program your set points. 

5. Turn the 

element breaker

 ON 

 

Section C – Fill in your Temperature Set Points for Reference

 

 

Temperature 

1 Group 

Factory 

2 Group 

3 Group 

Factory 

Zone 

1 

 200°  

  200° 

Zone 

2 

 250°  

  200° 

Zone 3 

N/A 

N/A 

* OFF 

 

200° 

Zone 4 

N/A 

N/A 

 

 

250° 

Zone 5 

N/A 

N/A 

 

 

250° 

•

  On a 2 group machine, lower the temperature setting for zone 3 until it reads OFF 

 

Section D - Scroll Mode 
 

•

  Turn ON by pressing 

up & down arrows

 together until scrolling starts 

•

  Turn OFF scroll mode by pressing either the 

set

 or 

zone

 button 

Summary of Contents for Sabre





















Reviews:

No comments

Brands by name

Popular brands

Load more brands