manualshive.com logo in svg

Symetrix 562E, User Manual, Page: 4 / 26

Share
Download
Symetrix 562E User Manual Download Page 4

562E

2

The information in this summary is intended
for persons who operate the equipment as well
as repair personnel. Specific warnings and
cautions are found throughout this manual
wherever they may apply.

The notational conventions used in this
manual and on the equipment itself are
described in the following paragraphs.

The lightning flash with arrowhead symbol
within an equilateral triangle is intended to alert
the user of the presence of uninsulated
"dangerous voltage" within the product's
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.

The exclamation point within an equilateral
triangle is intended to alert the user of the
presence of important operating and mainte-
nance (servicing) instructions in the literature
accompanying the 562E (i.e. this manual).

Caution

To prevent electric shock, do not
use the polarized plug supplied
with the 562E with any extension
cord, receptacle, or other outlet
unless the blades can be fully
inserted.

Terms

Several notational conventions are used in this
manual. Some paragraphs may use Note,
Caution, or Warning as a heading.  Certain
typefaces and capitalization are used to
identify certain words.  These are:

Note

Identifies information that needs
extra emphasis.  A Note generally
supplies extra information to help
you to better use the 562E.

Equipment Markings

Operator Safety Summary

Chapter 2

Caution

Identifies information that, if not
heeded, may cause damage to the
562E or other equipment in your
system.

Warning

Identifies information that, if

ignored, may be hazardous to
your health or that of others.

C

APITALS

      Controls, switches or other

                      markings on the 562E's chassis.

Boldface      Strong emphasis.

Power source - This product is intended to
operate from a power source that does not
apply more than 255Vrms between the power
supply conductors or between either power
supply conductor and ground. A protective
ground connection, by way of the grounding
conductor in the power cord, is essential for
safe operation.

Danger from loss of ground - If the protective
ground connection is lost, all accessible
conductive parts, including knobs and controls
that may appear to be insulated, can render an
electric shock.

Proper power cord - Use only the power cord
specified for the product. Use only a power
cord that is in good condition.

Operating location - Do not operate this
equipment under any of the following condi-
tions: explosive atmospheres, in wet locations,
in inclement weather, improper or unknown AC
mains voltage, or if improperly fused.

Stay out of the box - To avoid personal injury or
injury to others, do not remove the product
covers or panels. Do not operate the product
without the covers and panels properly
installed.

AVIS:

NE PAS OUVRIR

Il ne se trouve a l’interieur aucune piece pourvant entre reparée l’usager.

SEE OWNERS MANUAL. VOIR CAHIER D’INSTRUCTIONS.

S’adresser a un reparateur compétent.

RISQUE DE CHOC ELECTRIQUE

No user serviceable parts inside. Refer servicing to qualified service personnel.

CAUTION

WARNING:

TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK DO NOT EXPOSE
THIS EQUIPMENT TO RAIN OR MOISTURE

DO NOT OPEN

RISK OF ELECTRIC SHOCK

Summary of Contents for 562E



























Reviews:

No comments