562E
11
Connecting to Other Gear
Chapter 7
Matching Levels vs Matching Impedances
In any audio equipment application, the question of “matching” inevitably comes up. Without
digging a hole any deeper than absolutely necessary, we offer the following discussion to (hope-
fully) clarify your understanding of the subject.
Over the years, we have all had impedance matching pounded into our heads. This is important
only for ancient audio systems, power amplifiers, and RF. Technically speaking, the reason is
power transfer, which reaches a maximum when source and load are matched. Modern audio
systems are voltage transmission systems and source and load matching is not only unnecessary,
but undesirable as well.
r
Ancient audio systems operate at 600 ohms (or some other impedance value), and must be
matched, both at their inputs and at their outputs. Generally speaking, if you are dealing
with equipment that uses vacuum tubes, or was designed prior to 1970, you should be
concerned about matching. These units were designed when audio systems were based on
maximum power transfer, hence the need for input/output matching.
r
Power amplifiers are fussy because an abnormally low load impedance generally means a
visit to the amp hospital. Thus, it’s important to know what the total impedance of the pile
of speakers connected to the amplifier really is.
r
RF systems are matched because we really are concerned with maximum power transfer
and with matching the impedance of the transmission line (keeps nasty things from
happening). Video signals (composite, baseband, or otherwise) should be treated like RF.
Some folks seem to believe that balanced/unbalanced lines and impedances are related; or even
worse that they are associated with a particular type of connector. Not so. Unbalanced signals are
not necessarily high-impedance and balanced signals/lines are not necessarily low-impedance.
Similarly, although 1/4 inch jacks are typically used for things like guitars (which are high-imped-
ance and unbalanced), this does not predispose them to only this usage. After all, 1/4 inch jacks
are sometimes used for loudspeakers, which are anything but high-impedance. Therefore, the
presence of 3-pin XLR connectors should not be construed to mean that the input or output is low-
impedance (or high-impedance). The same applies to 1/4 inch jacks.
So, what is really important? Signal level, and (to a much lesser degree), the impedance relation
between an output (signal source) and the input that it connects to (signal receiver).
Signal level is very important. Mismatch causes either loss of headroom or loss of signal-to-noise ratio.
Thus, microphone inputs should only see signals originating from a microphone, a direct (DI) box, or an
output designated microphone-level output. Electrically, this is in the range of approximately -70 to -20
dBm. Line inputs should only see signals in the -10 to +24 dBm/dBu range. Guitars, high-impedance
microphones, and many electronic keyboards do not qualify as line-level sources.
The impedance relation between outputs and inputs needs to be considered, but only in the
following way - Always make sure that a device’s input impedance is higher than the output
source impedance of the device that drives it.
Some manufacturers state a relatively high-impedance figure as the output impedance of their
equipment. What they really mean is that this is the minimum load impedance that they would like
their gear to see. In most cases, seeing a output impedance figure of 10,000 (10K) ohms or higher
from modern equipment that requires power (batteries or AC) is an instance of this type of rating. If
so, then the input impedance of the succeeding input must be equal to or greater than the output
impedance of the driving device.
Symetrix equipment inputs are designed to bridge the output of whatever device drives the input
(i.e. to be greater than 10 times the actual source impedance). Symetrix equipment outputs are
designed to drive 600-ohm or higher loads (600-ohm loads are an archaic practice that won’t go
away). You don’t need to terminate the output with a 600-ohm resistor if you aren’t driving a 600-
ohm load. (If you don’t understand the concept of termination, you probably don’t need to
anyway.)
