manualshive.com logo in svg

Symetrix 562E, User Manual, Page: 14 / 26

Share
Download
Symetrix 562E User Manual Download Page 14

562E

12

The two facts that you need to derive from this discussion are:

r

Match signal levels for best headroom and signal-to-noise ratio.

r

For audio, impedance matching is only needed for vintage equipment and power amplifier
outputs.  In all other cases, ensure that your inputs bridge your outputs (meaning the
inputs are in the range of 2 to 200 times the output source impedance) .

Signal Levels

The 562E is designed around studio/professional line levels: +4 dBu or 1.23 volts RMS. The unit is
quiet enough to operate at lower signal levels such as those found in semipro or
musical-instrument (MI) equipment (-10 dBu or 300 millivolts).

I/O Impedances

The 562E is designed to interface into almost any recording studio or sound reinforcement applica-
tion. This includes:

r

600-ohm systems where input and output impedances are matched.

r

Unbalanced semiprofessional equipment applications.

r

Modern bridging systems where inputs bridge and outputs are low source impedances
(voltage transmission systems).

The 562E’s input impedance is greater than 20-kilohms balanced or 10K unbalanced. The inputs
may be driven from any source (balanced or unbalanced) capable of delivering at least -10 dBu into
the aforementioned impedances.

The 562E’s output impedance is 600 ohms balanced, 300 ohms unbalanced. The output line driver
de22 dBm into 600-ohm balanced loads or +18 dBm into 600-ohm unbalanced loads.

Polarity Convention

The 562E inputs and outputs use the international standard polarity convention of pin 2 hot.
Therefore, if your system uses balanced inputs and outputs, and uses the 562E this way, then the
polarity convention is unimportant. If your system is both balanced and unbalanced, then you
must pay attention to this, especially when going in and coming out through different connector
types (like input on an XLR, output on a phone jack).

XLR

1/4" Phone

Signal

Pin 1

Sleeve

Ground

Pin 2

Tip

High

Pin 3

Ring

Low

Input and Output Connections

The illustration on the next page shows how to connect the 562E to balanced and unbalanced
sources and loads.

To operate the 562E from unbalanced sources, run a 2-conductor shielded cable (that’s two
conductors plus the shield) from the source to the 562E. At the source, connect the low/minus side
to the shield, these connect to the source’s ground; connect the high/plus side to the source’s
signal connection. At the 562E, the high/plus wire connects to pin 2, the low/minus wire connects
to pin 3, and the shield (always) connects to pin 1. This is the preferred method as it makes best
use of the 562E’s balanced input (even though the source is unbalanced). The other alternative
shown in the illustration converts the 562E’s balanced input into an unbalanced input at the input
connector. This works, but is more susceptible to hum and buzz than the preferred method. There
is no level difference between either method.

Summary of Contents for 562E



























Reviews:

No comments