manualshive.com logo in svg

Symetrix 562E, User Manual, Page: 25 / 26

Share
Download
Symetrix 562E User Manual Download Page 25

562E

23

 Declaration of Conformity

Chapter 12

Declaration of Conformity

We, Symetrix Incorporated,

6408 216th St. SW, Mountlake Terrace, Washington, USA,

declare under our sole responsibility that the product:

562E Windowing Expander/Gate

to which this  declaration relates,

is in conformity with the following standards:

EN 60065

Safety requirements for mains operated electronic and related

apparatus for household and similar general use.

EN 50081-1

Electromagnetic compatibility - Generic emission standard

Part 1: Residential, commercial, and light industry.

EN 50082-1

Electromagnetic compatibility - Generic immunity standard

Part 1: Residential, commercial, and light industry.

EN 55022

Limits and methods of measurement of radio interference

characteristics of information technology equipment.

The technical construction file is maintained at:

Symetrix, Inc.

6408 216th St. SW

Mountlake Terrace, WA, 98043

USA

The authorized representative located within the European Community is:

World Marketing Associates

P.O. Box 34

Newquay, Cornwall, TR7 1TU, U.K.

Date of issue: 15 June, 1997

Place of issue:Mountlake Terrace, Washington, USA

Authorized signature:

Dane Butcher, President, Symetrix Incorporated.

Summary of Contents for 562E



























Reviews:

No comments