manualshive.com logo in svg

SycoTec e@syDrive 4624, Operating Manual, Page: 35 / 42

Share
Download
SycoTec e@syDrive 4624 Operating Manual Download Page 35

 
 

EN 

35 

Connection example: 

 

 

 

6.9 Mini USB connector 

 

4-pin mini USB connector  
 
The Mini USB connector is used to parameterize the frequency inverter by means of a PC. 

 

 

Frequency inverter 

PC / Tablet computer 

 

 

 

 

 
The virtual COM port is shown in the device manager as "USB Serial Port". 
If the driver is not installed automatically, then a current driver can be downloaded from the following 

manufacturer’s website and installed:

 

 

http://www.ftdichip.com/Drivers/VCP.htm 
 
The SycoDrive operating software finds the COM port automatically and creates a connection between the 
PC and the frequency inverter

.  

(Further information are available in the operating manual "Operating Software SycoDrive".) 

 

6.10 Micro SD card  

 

The micro SD card must be formatted as follows in order for the card to be recognized: 

•

 

FAT32 

 

Tested with Intenso MicroSDHC card 4 GB 

 

 

Only use the Micro SD Card provided, as a different Micro SD card may not be readable by the inverter.

 

 
The micro SD card is available for the following functions: 

•

 

Reading out the error memory of the frequency inverter,  

•

 

Parameter import, 

•

 

Parameter export, 

•

 

Firmware update. 

 (For more information, refer to the operating manual "Operating Software SycoDrive".) 

Summary of Contents for e@syDrive 4624











































Reviews:

No comments