manualshive.com logo in svg

SycoTec e@syDrive 4624, Operating Manual, Page: 19 / 42

Share
Download
SycoTec e@syDrive 4624 Operating Manual Download Page 19

 
 

EN 

19 

PLC input signal 

 

If the "Input for start:" is set to "Digital inputs", then starting is also possible via the PLC input.  

 

  

•

 

"Start" can only be used on the PLC input if it is disabled in the digital inputs. 

 

•

 

If the parameters are not transferred to the frequency inverter, then the settings will not take effect. 

 

  ATTENTION 

 

Automatic start-up after a mains failure where a start signal is present at DIN1 or at the PLC input is 
prevented. A positive edge is required at the start input. 

 

 

 

CAN  

 

The "Input for start" can also be set to "CAN". The "CAN node ID" can then be configured in the 
"INPUTS/OUTPUTS" category under "CAN". 
 

   If the frequency inverter stops with an error, a start is only possible again if the button "Save on 

inverter" of the software SycoDrive has been activated before (only for the combination "Input for start" 
via Digital inputs and "Inputs for rated frequency" via SycoDrive), 

Summary of Contents for e@syDrive 4624











































Reviews:

No comments