manualshive.com logo in svg

SWF E-U1201, Manual, Page: 15 / 67

Share
Download
SWF E-U1201 Manual Download Page 15

SAFETY RULES FOR MACHINE OPERATION

05

16

5.1) TYPES OF SAFETY LABELS

※

※

Watch Out for Needle!

When threading needles or replacing the needles, make sure to stop the
machine. Otherwise, you may get your hands hurt.

※

※

Watch Out for High-Voltage Electricity!

You may get an electric shock. Except for A/S service engineers, do not
open the cover. To open the cover, turn off the power and wait for 6
minutes before opening the cover. 

※

※

Watch Out for the Opening!

Do not insert your hands stuck between the tables.

※

※

Do not place your hand!

If your hand is placed between the frame and the machine structure,
depending on the moving direction of the frame, you may get your
hands hurt.

※

※

Watch Out for Spinning!!
Make sure to close the cover before operating the machine. While the
machine is in operation, do not keep your hands close to the machine
parts, which are in motion. Otherwise, you may get your hands hurt. 

※

※

Watch Out for Spinning!

While the machine is in operation, keep your hands away from the
needle bar and the thread take-up. 

Fully understand the contents of the safety labels attached to the machine to prevent any
safety accidents from occurring.

CAUTION

Injury may be caused by moving
needle.

Ensure that the machine is in a
stop condition before changing,
threading or rethreading of
needies or changing of needles.

WARNING

WARNING

Fire or death may be caused by
high voltage electric shock.
Don’t open the cover except for
service man assigned by SWF.
When open the cover turn off
power and wait for 6 minutes.

WARNING

Physical injury may be caused

by crevice.

Don

’

t put your finger in a groove

on the table.

Physical damage may be caused
by interposition.
While embroidery frame is running
according to the direction of
embroidery frame may be injured
your hands by gap between fixed
body and embroidery frame.

WARNING

Injury may be caused by winding.

Be sure to turn off the power

before  cleaning, lubricating,

adjusting or repairing.

WARNING

Physical damage may be caused by
winding.

Don’t put your hands near the 
needle bar & take-up lever while 
machine is running.

WARNING

Summary of Contents for E-U1201




































































Reviews:

No comments