swaploader SL-240 Parts And Operation Manual Download | Manualshive

Page: 19 / 140

background image

SL-240.INS

2-1

05/2020

INITIAL INSPECTION

When the hoist is installed and ready for delivery, it is your responsibility to fill out and submit
the Product Registration Form. Visit

https://www.swaploader.com/warranty-registration/

to

complete this form.
When the SwapLoader hoist is received from the factory, you should inspect the hoist for
damage, which may have occurred in shipment. If damage has occurred, you should contact the
shipper immediately. Be sure to note any damage or missing items on bill of Lading.
When you receive your SwapLoader hoist, it is your responsibility to make sure you have
received all the parts and pieces that were ordered, within 30 days of the invoice date of the
hoist. Lay out all the options, loose parts and accessories on a table and compare the items
received vs the Packing List and the Loose Parts Box List(s) shipped with the hoist order.
If you have any problems, shortages, or questions, please contact SwapLoader U.S.A., Ltd.
immediately.

GENERAL INSTALLATION PROCEDURE

The installation of the SwapLoader on a truck chassis will generally follow these steps:

1.

Install hoist assembly onto truck chassis.

2.

Mount the hydraulic control valve to the hoist and install the hydraulic plumbing from the
control valve to the hydraulic cylinders. Then install the control levers in the cab and
route the control cables to the hydraulic control value assembly.

3.

Install the hydraulic tank, hydraulic filter, and hydraulic plumbing between the hydraulic
tank and the control valve assembly.

4.

Select and install the P.T.O. on the truck transmission. (Note: This can be done prior to
hoist installation on the truck chassis.)

5.

Install the hydraulic pump and the plumbing from the pump to the hydraulic tank and
control valve assembly.

6.

Fill the hydraulic tank with oil, bleed the air from the pump suction line, and start up the
unit.

Although SwapLoader attempts to include the mounts and attaching fasteners with each hoist
unit, your particular installation may require some additional mounts or modifications. If you
have problems with your installation, please contact SwapLoader at 1-888-767-8000, as we may
be aware of another customer who has installed a SwapLoader on a similar truck chassis.

«
...
17
18
19
20
21
...
»

Summary of Contents for SL-240













































































































































Reviews:

No comments

Related manuals for SL-240

Brand: swaploader Pages: 92

Brand: Sovan's Pages: 45

Brand: DAF Pages: 254

Brand: Magliner Pages: 64

Brand: U-Line Pages: 6

Brand: Isuzu Pages: 580

Torrent BX7540P

Brand: Blue Ox Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands