manualshive.com logo in svg

Sutron MONITOR, Operation & Maintenance Manual

Share
Download
Sutron MONITOR Operation & Maintenance Manual Download Page 6

DB9 Connector 

MONITOR comes with a DB9F connector for connection to RS-232 devices.  The DB9F 
can be connected to the serial port on most PCs using a straight cable.  A null modem 
adapter is needed to connect to most PDAs and modems.  There is a 

command line 

interface

 that allows communication via RS-232. 

 
The following table shows the pin assignments in the DB9F connector. 
 

DB9F Pin Name

 

Notes 

1 N/C  No 

Connection 

2 RXD  Data 

from 

MONITOR 

3 

TXD 

Data to MONITOR 

4 DTR  Signal 

to 

MONITOR 

5 Ground 

 

6 N/C  No 

Connection 

7 

RTS 

Request to Send, signal to MONITOR 

8 

CTS 

Clear to Send, signal from MONITOR 

9* VOUT 

Jumper selectable for 5V or VBAT 
(100ma max) 

 
*Pin 9 can be used to provide 12V, 5V or no voltage.  Certain devices, such as Bluetooth 
dongles require power on that pin.  Any setting will work for talking to a PC. 
 
What voltage is output is controlled by an internal jumper.  To setup the jumper, the case 
must be opened.  Once the case is open, the jumper is easily accessible.  The Jumper in 
question is J19, and is located next to the RS232 connector.  Set the jumper across pins 1 
and 2 to provide 12V, across pins 2 and 3 to provide 5V, or remove jumper to have no 
voltage output.   
 
Another jumper J16 (located near J19) determines when MONITOR outputs the voltage 
on pin 9.  If the jumper is across pins 1 and 2, MONITOR will always output the voltage 
on pin 9.  Any other configuration will cause MONITOR to output the voltage only when 
it is using the RS232 port (such as when it’s talking to a PC or a GPS). 

6 

 

Summary of Contents for MONITOR

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands