THREE-PHASE MODELS
IN THE CASE OF THREE-PHASE MODELS,
SWAPPING TWO PHASES MAY CAUSE THE
ELECTRIC MOTORS TO RUN IN THE REVERSE
DIRECTION, WHICH CAN CAUSE DAMAGE. AS A
PREVENTATIVE MEASURE, THE UNIT HAS A BUILT-IN
PROTECTIVE DEVICE THAT BREAKS THE CIRCUIT IF THE
CONNECTION IS INCORRECT. IF THE RED LED ABOVE THIS
SAFETY DEVICE LIGHTS UP, THE CONNECTIONS OF THE
TWO PHASE WIRES MUST BE SWAPPED.
Instal Connection
Heatseker Nova Inverter Heat Pump
supremeheating.com.au 11
After all connections have been made and checked, carry out following
procedure:
1
Switch on the filter pump. Check for leaks and verify that water is
flowing to and from the swimming pool.
2
Connect power to the heat pump and press the On/Off
Button on the automatic control panel. The unit will start
up after the time delay expires.
3
After a few minutes, check whether the air blowing out of the unit
is cooler.
4
When the filter pump is turned off; the unit should also turn off
automatically. If this does not occur adjust the Water Flow Switch
(detailed below).
5
Allow the heat pump and the filter pump to run 24 hours a day
until the desired water temperature is reached.
Once the temperature is reached, the heat pump will stop running.
When the swimming pool water drops 2°C below the set
temperature, the heat pump will restart automatically.
Dependant on the initial temperature of the water in the swimming
pool and the air temperature, it may take several days for the water to
heat to the water to the desired temperature.
A quality
Supreme
Heating Heatseeker Diamond Pool Cover & Roller
System can dramatically reduce the required heat up time.
Water Flow Switch
The heat pump is equipped with a flow switch to ensure the unit is
operating with an adequate water flow rate. The flow switch will
detect flow through the heat exchanger and allow the heat pump to
continue running. If the water flow is interrupted or stopped, the flow
switch will trigger the heat pump to turn off.
Time Delay
The heat pump has a built-in 3 minute start-up delay to protect the
circuitry and avoid excessive contact wear. The unit will restart
automatically after this time delay expires. If a breif power interruption
After all connections have been made and checked, carry out following
procedure:
1
Switch on the filter pump. Check for leaks and verify that water is
flowing to and from the swimming pool.
2
Connect power to the heat pump and press the On/Off
Button on the automatic control panel. The unit will start
up after the time delay expires.
3
After a few minutes, check whether the air blowing out of the unit
is cooler.
4
When the filter pump is turned off; the unit should also turn off
automatically. If this does not occur adjust the Water Flow Switch
(detailed below).
5
Allow the heat pump and the filter pump to run 24 hours a day
until the desired water temperature is reached.
Once the temperature is reached, the heat pump will stop running.
When the swimming pool water drops 2°C below the set
temperature, the heat pump will restart automatically.
Dependant on the initial temperature of the water in the swimming
pool and the air temperature, it may take several days for the water to
heat to the water to the desired temperature.
A quality
Supreme
Heating Heatseeker Diamond Pool Cover & Roller
System can dramatically reduce the required heat up time.
Water Flow Switch
The heat pump is equipped with a flow switch to ensure the unit is
operating with an adequate water flow rate. The flow switch will
detect flow through the heat exchanger and allow the heat pump to
continue running. If the water flow is interrupted or stopped, the flow
switch will trigger the heat pump to turn off.
Time Delay
The heat pump has a built-in 3 minute start-up delay to protect the
circuitry and avoid excessive contact wear. The unit will restart
automatically after this time delay expires. If a breif power interruption
ACCESSORIES
Heatseker Nova Inverter Heat Pump
supremeheating.com.au 12
occurs this will trigger the time delay and prevent the unit from
restarting immediately.
3.8 CONDENSATION
The air drawn into the heat pump is cooled by the operation of the
heat pump for heating the pool water, which may cause condensation
on the fins of the evaporator. The amount of condensation may be as
much as several liters per hour at high relative humidity.
4. ACCESSORIES
4.1 ACCESSORIES LIST
4 x Anti-vibration Base Controller Cover Extension Cable 2 x Draining
Jet
2 x Water Connection Assembly Winter Cover Drainage Hose
4.2 INSTALLATION OF ACCESSORIES
1
Anti-vibration bases Drainage Point
(SIDE DISCHARGE ONLY)
1
Place 1 anti-vibration base
2
Install the drainage point under
under each corner of the heat the bottom of the heat pump.
pump.
2
Connect with the draining hose
to drain out the water.
Summary of Contents for heatseeker nova
Page 1: ......
