Supero SuperServer 6027PR-HC1FR User Manual Download Page 124

Page: 124 / 138

7-28

SUPERSERVER 6027PR-HC1(R/TR/FR) USER'S MANUAL

7-3 Event Logs

Select the Event Logs tab to access the following submenu items.



Change SMBIOS Event Log Settings

This feature allows the user to configure SMBIOS Event settings.

Enabling/Disabling Options

SMBIOS Event Log

Select Enabled to enable SMBIOS (System Management BIOS) Event Logging
during system boot. The options are

Enabled

and Disabled.

Runtime Error Logging Support

Select Enabled to support Runtime Error Logging. The options are

Enabled

and

Disabled.

Memory Correctable Error Threshold

This feature allows the user to enter the threshold value for correctable memory
errors. The default setting is

Summary of Contents for SuperServer 6027PR-HC1FR











































































































































Search results

Summary of Contents for SuperServer 6027PR-HC1FR

Reviews:

Related manuals for SuperServer 6027PR-HC1FR

Brands by name

Popular brands

Supero SuperServer 6027PR-HC1FR, User Manual

Search results

Summary of Contents for SuperServer 6027PR-HC1FR

Reviews:

Related manuals for SuperServer 6027PR-HC1FR

Brands by name

Popular brands