Supero SuperServer 6027PR-HC1FR User Manual Download Page 94

Page: 94 / 138

6-18

SUPERSERVER 6027PR-HC1(R/TR/FR) USER'S MANUAL

Installing the Hard Drive (Figure 6-17)

1. Install a new drive into the carrier with the printed circuit board side facing down

so that the mounting holes align with those in the carrier.

2. Secure the hard drive by tightening all six (6) screws.

3. Use the open handle to replace the drive tray into the chassis. Make sure the

close the drive tray handle.

Figure 6-17. Installing the Hard Drive

Drive Tray

SATA Hard Drive

Caution:

Enterprise level hard disk drives are recommended for use in Supermicro

chassis and servers. For information on recommended HDDs, visit the Supermicro

Web site at http://www.supermicro.com/products/nfo/files/storage/SAS-CompList.pdf

Summary of Contents for SuperServer 6027PR-HC1FR











































































































































Search results

Summary of Contents for SuperServer 6027PR-HC1FR

Reviews:

Related manuals for SuperServer 6027PR-HC1FR

Brands by name

Popular brands

Supero SuperServer 6027PR-HC1FR, User Manual

Search results

Summary of Contents for SuperServer 6027PR-HC1FR

Reviews:

Related manuals for SuperServer 6027PR-HC1FR

Brands by name

Popular brands