Supero SuperServer 6027PR-HC1FR User Manual Download Page 16

Page: 16 / 138

1-8

SUPERSERVER 6027PR-HC1(R/TR/FR) USER'S MANUAL

1-6 Contacting Supermicro

Headquarters

Address:

Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.

Tel:

+1 (408) 503-8000

Fax:

+1 (408) 503-8008

Email:

[email protected] (General Information)
[email protected] (Technical Support)

Web Site:

www.supermicro.com

Europe

Address:

Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands

Tel:

+31 (0) 73-6400390

Fax:

+31 (0) 73-6416525

Email:

[email protected] (General Information)
[email protected] (Technical Support)
[email protected] (Customer Support)

Web Site:

www.supermicro.nl

Asia-Pacific

Address:

Super Micro Computer, Inc.
3F, No. 150, Jian 1st Rd.
Zhonghe Dist., New Taipei City 235
Taiwan (R.O.C)

Tel:

+886-(2) 8226-3990

Fax:

+886-(2) 8226-3992

Email:

[email protected]

Web Site:

www.supermicro.com.tw

Summary of Contents for SuperServer 6027PR-HC1FR











































































































































Search results

Summary of Contents for SuperServer 6027PR-HC1FR

Reviews:

Related manuals for SuperServer 6027PR-HC1FR

Brands by name

Popular brands

Supero SuperServer 6027PR-HC1FR, User Manual

Search results

Summary of Contents for SuperServer 6027PR-HC1FR

Reviews:

Related manuals for SuperServer 6027PR-HC1FR

Brands by name

Popular brands