Supero SUPERSERVER 1026TT-IBQF User Manual Download Page 98

Page: 98 / 102

B-2

UPER

ERVER 1026TT-TF/1026TT-IBXF/1026TT-IBQF User's Manual

B-2 Installing Windows for a Non-RAID System

Insert Microsoft's Windows XP/2003 Setup CD in the CD drive and the sys-

tem will start booting up from CD.

Continue with the OS installation. The Windows OS Setup screen will display.

From the Windows XP/2003 Setup screen, press the <Enter> key. The

XP/2003 Setup will automatically load all device fi les and then continue with

the Windows XP/2003 installation.

After the Windows XP/2003 OS Installation is completed, the system will auto-

matically reboot.

Insert the Supermicro Setup CD that came with your motherboard into the CD

Drive during system boot, and the main screen will display.

Summary of Contents for SUPERSERVER 1026TT-IBQF







































































































Search results

Summary of Contents for SUPERSERVER 1026TT-IBQF

Reviews:

Related manuals for SUPERSERVER 1026TT-IBQF

Brands by name

Popular brands

Supero SUPERSERVER 1026TT-IBQF, User Manual

Search results

Summary of Contents for SUPERSERVER 1026TT-IBQF

Reviews:

Related manuals for SUPERSERVER 1026TT-IBQF

Brands by name

Popular brands