Supero SuperServer 1025C-M3 User Manual Download Page 30

Page: 30 / 110

3-2

UPER

ERVER 1025C-M3 Manual

3-3 Control Panel LEDs

The control panel located on the front of the SC113MTQ-560CB chassis has four

LEDs. These LEDs provide you with critical information related to different parts of

the system. This section explains what each LED indicates when illuminated and

any corrective action you may need to take.

NIC1

Indicates network activity on LAN1 when fl ashing.

NIC2

Indicates network activity on LAN2 when fl ashing.

HDD

Indicates IDE channel activity when fl ashing.

Power

Indicates power is being supplied to the system's power supply units. This LED

should normally be illuminated when the system is operating.

Summary of Contents for SuperServer 1025C-M3















































































































Search results

Summary of Contents for SuperServer 1025C-M3

Reviews:

Related manuals for SuperServer 1025C-M3

Brands by name

Popular brands

Supero SuperServer 1025C-M3, User Manual

Search results

Summary of Contents for SuperServer 1025C-M3

Reviews:

Related manuals for SuperServer 1025C-M3

Brands by name

Popular brands