Supero Super 370DE6 User Manual Download Page 90

Page: 90 / 104

UPER 370DE6/370DER/370DEI

User's Manual

4-28

BIOS

Change Supervisor Password

This option allows you to change a supervisor password that was entered

previously.

Change User Password

This option allows you to change a user password that was entered previ-

ously.

Clear User Password

Use this option to clear the user password so that it is not required to be

entered when the system boots up.

Boot Sector Virus Protection

This option allows you to enable or disable a virus detection program to

protect the boot sector of your hard disk drive. The settings for this option

Disabled and Enabled. If Enabled, AMIBIOS will display a warning when

any program (or virus) issues a Disk Format command or attempts to write

to the boot sector of the hard disk drive.

Summary of Contents for Super 370DE6









































































































Search results

Summary of Contents for Super 370DE6

Reviews:

Related manuals for Super 370DE6

Brands by name

Popular brands

Supero Super 370DE6, User Manual

Search results

Summary of Contents for Super 370DE6

Reviews:

Related manuals for Super 370DE6

Brands by name

Popular brands