Supero Super 370DE6 User Manual Download Page 86

Page: 86 / 104

UPER 370DE6/370DER/370DEI

User's Manual

4-24

BIOS

Suspend Timeout

This option specifies if BIOS is to monitor for display activity when in a

power saving state. The settings include Off, 1, 2, 3, 4, 5, 6, 7, 8, 9 and 10

(minutes).

IRQ1

IRQ3

IRQ4

IRQ5

IRQ6

IRQ7

IRQ9

IRQ10

IRQ11

IRQ12

IRQ14

IRQ15

With the above options, you can monitor each interrupt request and resume

the system's normal power up state when activated. Settings are Ignore

and Monitor. All IRQs are defaulted to Ignore except for IRQ 1, 12 and 14,

whcih default to Monitor.

USB Controller Resume

This allows you to wake up the system from a USB device. The settings for

this option Disabled and Enabled.

RI Resume

This option allows the system to resume the function of Ring Indicator. The

settings for this option Disabled and Enabled.

PME R e s u m e

This allows you to wake up the system from a PME device. The settings for

this option Disabled and Enabled.

Summary of Contents for Super 370DE6









































































































Search results

Summary of Contents for Super 370DE6

Reviews:

Related manuals for Super 370DE6

Brands by name

Popular brands

Supero Super 370DE6, User Manual

Search results

Summary of Contents for Super 370DE6

Reviews:

Related manuals for Super 370DE6

Brands by name

Popular brands