Supero Super 370DE6 User Manual Download Page 29

Page: 29 / 104

UPER 370DE6/370DER/370DEI User's

Manual

1-22

Introduction

ACPI/PC 98 Features

•

Microsoft OnNow

•

Slow blinking LED for suspend state indicator

•

Main switch override mechanism

•

External modem ring-on

Onboard I/O

•

AIC-7899 for dual channel Ultra160 SCSI (370DE6/370DER/)

•

Integrated ATI Rage XL Graphics Controller (370DER//370DEI)

•

Intel 82559 for integrated onboard Ethernet (370DER//370DEI)

•

2 EIDE bus master interfaces support Ultra DMA/33

•

1 floppy port interface (up to 2.88 MB)

•

2 Fast UART 16550A compatible serial ports

•

1 EPP/ECP (Enhanced Parallel Port/Extended Capabilities Port)

(370DE6/370DER/370DEI)

•

PS/2 mouse and PS/2 keyboard ports

•

2 USB (Universal Serial Bus) ports

Other

•

Internal/external modem ring-on

•

Recovery from AC power loss control

•

Wake-on-LAN (WOL)

CD/Diskette Utilities

•

BIOS flash upgrade utility

•

Device Drivers

Dimensions

•

SUPER 370DE6

Extended ATX: 12.05" x 13" (306 x 330 mm)

•

SUPER 370DER//370DEI

Full ATX: 12.05" x 11.475" (306 x 291 mm)

Summary of Contents for Super 370DE6









































































































Search results

Summary of Contents for Super 370DE6

Reviews:

Related manuals for Super 370DE6

Brands by name

Popular brands

Supero Super 370DE6, User Manual

Search results

Summary of Contents for Super 370DE6

Reviews:

Related manuals for Super 370DE6

Brands by name

Popular brands