Supero AS-1011M-UR User Manual Download

Page: 80 / 104

7-8

AS1011M-UR User's Manual

drive support. Select "Disabled" to prevent AMI BIOS from using the S.M.A.R.T.

Select "Enabled" to allow AMI BIOS to use the S.M.A.R.T. to support hard drive

disk. The options are Disabled, Enabled, and

Auto

32-Bit Data Transfer

Select "Enabled" to activate the function of 32-Bit data transfer. Select "Disabled"

to deactivate the function. The options are

Enabled

and Disabled.

Hard Disk Write Protect

Select Enabled to enable the function of Hard Disk Write Protect to prevent data

from being written to HDD. The options are Enabled or

Disabled

IDE Detect Time Out (Sec)

This feature allows the user to set the time-out value for detecting ATA, ATA PI

devices installed in the system. The options are 0 (sec), 5, 10, 15, 20, 25, 30 and

ATA(PI) 80Pin Cable Detection

This setting allows AMI BIOS to auto-detect the 80-Pin ATA(PI) cable. The options

are

Host, Device and

Host & Device

Summary of Contents for AS-1011M-UR









































































































Search results

Summary of Contents for AS-1011M-UR

Reviews:

Related manuals for AS-1011M-UR

Brands by name

Popular brands

Supero AS-1011M-UR, User Manual

Search results

Summary of Contents for AS-1011M-UR

Reviews:

Related manuals for AS-1011M-UR

Brands by name

Popular brands